Split-Hinge Tube Furnaces

Thermo Scientific - HTF55122A

Designed for horizontal or vertical operation
Patented Moldatherm LGO heating element modules for superior radial and linear temperature uniformity, fast heat-up and cool-down
Long-life, energy-efficient elements require little or no maintenance

Fast response from our specialists

Single Zone and Three Zone

Lindberg/Blue M 1200°C split hinge tube furnaces are configurable for horizontal or vertical use. Choose from single zone models of 12" and 24" heated lengths, and three zone models of 24" to 36" heated lengths. Furnaces use independent digital temperature control modules (ordered separately) which are available in standard or programmable options.

The split-hinge design permits easy observation, fast cooling, convenient placement of the process tube and overall ease of operation. All models can be used with a variety of ceramic, quartz or alloy process tubes (customer supplied),diameters to 6" depending on model. One set of tube adapters is included with each model.

Features

Designed for horizontal or vertical operation
Patented Moldatherm LGO heating element modules for superior radial and linear temperature uniformity, fast heat-up and cool-down
Long-life, energy efficient elements require little or no maintenance
Unique cabinet design achieves lower exterior surface temperature
Heat reflecting element support assembly creates two highly effective insulating air spaces
Compact cabinet with high temperature resistant painted finish
Accepts interchangeable Moldathermâ tube adapters
Long-life Platinelâ II thermocouple(s) with 10' compensated lead wire and polarized plug
RS-485 communication port available as an option.

Three zone models:

Three independent power circuits (zones) with independent thermocouples for control references
Full adjustment of each zone over entire operating range to 1200°C
Center zone uniformity achieved and operating length maximized through adjustable profiling of end zones by independent controller
Temperature uniformity achieved with independent setpoint of end zones higher or lower than center

Floor stand for vertical installation
The optional Floor Stand is required to support HTF Series Tube Furnaces in a vertical configuration. Floor stands include all mounting hardware.1200°C LGO Split-Hinge Tube Furnaces can be used in a horizontal or vertical configuration.
	Single Zone	HTF55122A	HTF55322A HTF55322C	HTF55342C
	Three Zone			HTF55347C	HTF55667C
Floor Stand Model		VFS551	VFX553
Floor Stand Model				VFS553	VFS553
Floor Stand Model					VFS556

Tube adapters
Tube adapters prevent heat loss and improve temperature uniformity within the furnace chamber by insulating the end vestibules. One set (2) of tube adapters provided with each Lindberg/Blue M furnace fits the largest diameter process tube specified for use with that furnace. Interchangeable tube adapters which allow alternative size process tubes are available; see chart.
Size	Model STF55346C	Model STF55666C
1 in.	59541
2 in.	59543
3 in.	59545*	59555
4 in.		59556
5 in.		59557
6 in.		59558*
Blank (Solid)	59549	59559
Note: Power cord and hard wiring supplied by costumer. Contact us for CE Models Actual performance may vary depending on load, chamber size, sample placement, ambient temperature and environmental conditions.

Single zone controllers
1200°C Digital, Single Setpoint Controller
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jack. Includes microprocessor-based PID control (proportional, integral, derivative),single segment, single setpoint, 1 ramp to setpoint. Built-in adjustable high limit overtemperature protection. Simultaneous LED display of actual temperature vs. setpoint. May be configured to display temperature in either °C or °F.
1200°C Digital 16 Segment Programmable Controller
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jack. Includes microprocessor-based PID control (proportional, integral, derivative),1 program with 16 segments, for ramp (up and down) and dwell (timed holds). Built-in adjustable high limit overtemperature protection. Simultaneous LED display of actual temperature vs. setpoint. May be configured to display temperature in either °C or °F.
Option B Overtemperature Control (OTC)
Adjustable digital overtemperature control, factory installed on selected control consoles with "B" designation; see chart. Protects furnace and load in the event of primary control circuit failure. Overrides main controller, assumes temperature control and shuts off power to furnace if high limit is reached. Manual re-set required for safety. Operates via magnetic contacts through signal from independent thermocouple. RS-485 communication port available as an option
MODEL	CC58114A	CC58114C	CC58114PA	CC58114PC	CC58114PBA	CC58114PBC
Digital	X	X	X	X	X	X
With Programmer			X	X	X	X
With Overtemp. Control					X	X
Electrical Volts, Hz	120V, 50/60Hz	208/240V, 50/60Hz	120V, 50/60Hz	208/240V, 50/60Hz	120V, 50/60Hz	208/240V, 50/60Hz
Ext. (WxF-BxH)	14 x 19 x 10 in. (35.5 x 48.3 x 25.4 cm)
Ship Weight	40lb (19kg)	40lb (19kg)	40lb (19kg)	40lb (19kg)	45lb (21kg)	45lb (21kg)

Three zone controllers
1200°C Three Zone Controller - Option One
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone. Includes three microprocessor-based PID controls (proportional, integral,derivative),single segment, single setpoint, 1 ramp to setpoint. Built-in adjustable high limit overtemperature protection. Simultaneous LED display of actual temperature vs. setpoint. May be configured to display temperature in either °C or °F.
Option B Overtemperature Control (OTC)
Adjustable digital overtemperature control, factory installed on selected control consoles with "B" designation; see chart. Protects furnace and load in the event of primary control circuit failure. Overrides main controller, assumes temperature control and shuts off power to furnace if high limit is reached. Manual re-set required for safety. Operates via magnetic contacts through signal from independent thermocouple. Available system on all three zone controller varieties. RS-485 communications port available as an option.
MODEL		CC58434C
Digital
With Programmer
With Overtemp. Control
Electrical Volts, Hz		208/240V, 50/60Hz
Max Amps		20/30/20
Ext. (WxF-BxH)		14 x 19 x 17 in. (35.5 x 48.3 x 43.2 cm)
Ship Weight		60lb (28kg)
1200°C Three Zone 16 Segment One Programmable Controller - Option Two
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.
Center Zone
One microprocessor-based PID programmable control (proportional, integral, derivative),with 1 program of16 segments for ramps (up and down) and 8 dwells (timed holds). Built-in adjustable high limit overtemperature protection. Simultaneous LED display of actual temperature vs. setpoint.
End Zones
Two microprocessor-based PID control (proportional, integral, derivative),single segment, single setpoint which mimic the programmed profile of the center zone controller, but allow an offset up to 100°C. Offset is digitally displayed. RS-485 communications port available as an option.
MODEL	CC58434PC	CC58434PBC
Digital	X	X
With Programmer	X	X
With Overtemp. Control
Electrical Volts, Hz	208/240V, 50/60Hz	208/240V, 50/60Hz
Max Amps	20/30/20	20/30/20
Ext. (WxF-BxH)	14 x 19 x 17 in. (35.5 x 48.3 x 43.2 cm)	14 x 19 x 17 in. (35.5 x 48.3 x 43.2 cm)
Ship Weight	60lb (28kg)	65lb (30kg)
1200°C Three Zone 16 Segment Three Programmable Controllers - Option Three
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone. Includes three microprocessor-based PID programmable controllers (proportional, integral, derivative),with 1 program of 16 segments for ramps (up and down) and 8 dwells (timed holds) to control each zone separately. Built-in adjustable high limit overtemperature protection. Simultaneous LED display of actual temperature vs. setpoint. May be configured to display temperature in either °C or °F.
MODEL	CC58434PC	CC58434PBC
Digital	X	X
With Programmer	X	X
With Overtemp. Control
Electrical Volts, Hz	208/240V, 50/60Hz	208/240V, 50/60Hz
Max Amps	20/30/20	20/30/20
Ext. (WxF-BxH)	14 x 19 x 17 in. (35.5 x 48.3 x 43.2 cm)	14 x 19 x 17 in. (35.5 x 48.3 x 43.2 cm)
Ship Weight	60lb (28kg)	65lb (30kg)

Model	Independent	Electrical, 1Ø	Watts	Ext.	*Process Tube	Heated	Ship
	Controller			(WxF-BxH)	(diameter)	Length	Weight
Single Zone - 1200°C Split Hinge, Horizontal or Vertical use, Temp. Range 100 to 1200°C
HTF55122A	CC58114A	120V,	1330	13x21x12 in.	0.75 to 1 in.	12 in.	60lbs
		50/60 Hz		33x53.3x30.5cm	(1.9 to 2.54cm)	(30.48cm)	(28kg)
HTF55322A	CC58114A	120V,	2675	17x23x16 in.	1 to 3 in.	12 in.	120lbs
		50/60 Hz		43.2x58.4x40.6cm	(2.54 to 7.62cm)	(30.48cm)	(55kg)
HTF55322C	CC58114C	208/240V,	2675	17x23x16 in.	1 to 3 in.	12 in.	120lbs
		50/60Hz		43.2x58.4x40.6cm	(2.54 to 7.62cm)	(30.48cm)	(55kg)
HTF55342C	CC58114C	208/240V,	5440	17x23x16 in.	1 to 3 in.	24 in. (60.96cm)	175lbs
		50/60Hz		43.2x58.4x40.6cm	(2.54 to 7.62cm)		(80kg)
Tube adapters: One set of (2) included with furnace: Model HTF55122A, (2) 1 in. dia. adapters; Models HTF55322A/C, (2) 2 in. dia. adapters; Model HTF 55342C, (2) 2.5 in. dia. adapters.
Three Zone - 1200°C Split Hinge, Horizontal or Vertical use, Temp. Range 100 to 1200°C
HTF55347C	CC58434C	208/240V,	5355	17x35x16 in.	1 to 3 in.	24 in. (60.96cm)	195lbs (89kg)
		50/60Hz		(43.2x88.9x40.6 cm)	(2.54 to 7.62cm)
HTF55667C	CC58434C	208/240V,	11760	3x49x20 in.	3 to 6 in.	36 in.	310lbs
		50/60Hz		(53.3x124.5x50.8cm)	(7.62 to 15.24cm)	(91.4cm)	(141kg)
Tube adapters: One set of (2) included with furnce: Model HTF55347C, (2) 2.5 in. dia. adapters; Models HTF55667C, (2) 3 in. dia. adapters.
* Process Tubes: These furnaces are designed for use with a variety of process tubes including alumina, mullite, quartz and metallic. Process tube is not supplied with furnace. For information on process tubes contact us. One set of (2) tube adapters included with furnace; largest specified size supplied.