- Solinst - 122
- Conçu pour le terrain
- Électroniques stables avec test des circuits automatiques
- Ruban gradué en PVDF avec marquage au laser facile à décontaminer
Modèle : SO110667-0
Modèle : SO110650-0
Modèle : SO112213-0
Modèle : SO110651-0
Modèle : SO110657-0
Modèle : SO110658-0
Modèle : SO110666-0
Modèle : SO110643-0
Modèle : SO110644-0
Modèle : SO110645-0
Modèle : SO110649-0
Modèle : SO110932-0
Modèle : SO112212-0
Modèle : SO110642-0
Solinst 122 Oil/Water Interface Meters give clear and accurate measurements of product level and thickness in wells and tanks.
Determination of both light (floating) non-aqueous phase liquids (LNAPL) and dense (sinking) non-aqueous phase liquids (DNAPL) is quick and easy. The factory-sealed probe is pressure proof (up to 500 psi) and tapes are available in a range of lengths from 100 - 1000 ft (30 - 300 m). The 5/8" (16 mm) diameter probe allows easy access through tight spaces and into narrow wells. The probe is designed for use in various monitoring applications.
Hazardous Locations Use
The Model 122 Interface Meter with laser marked PVDF tape is now ATEX certified under directive 94/9/EC, as II 3 G Ex ic IIB T4 Gc. The grounding strap is a safety essential when the meter is used in potentially explosive environments. It also ensures that the electronics are properly protected.
Water (Conductive liquid) = Intermittent light and tone.To detect liquids, Solinst Interface Meters use an infra-red beam and detector. When the probe enters a liquid the beam is refracted away from the detector which activates an audible tone and light. If the liquid is a non-conductive oil/product the signals are steady. If the liquid is water (conductive liquid greater than 20 μS/cm), the conductivity of the water completes a conductivity circuit. This overrides the infra-red circuit, and the tone and light are intermittent. The 122 Interface Meter sensor provides an accuracy as good as 1/200 ft or 1.0 mm. The high accuracy enables the sensor to detect the slightest sheen of oil on the surface of the water.
Accurate, Reliable, Robust
- Designed for rugged field use
- Stable electronics with automatic circuitry testing
- Laser marked PVDF flat tape is easy to decontaminate; resists stains
- Tape uses stranded stainless steel and copper coated steel conductors:
- High in tensile strength; electrical efficiency
- Non-stretch; does not corrode
- Sturdy free-standing reel with carrying handle
High Quality Design
Infra-red refraction is used to detect liquids and conductivity to distinguish water. Both optical and electronic sensors are
precisely aligned at the same zero point. The factory sealed probe does not need to be accessed by the user. An integral stainless steel shield protects the sensors. It is set permanently into place, yet allows for easy cleaning.
- Sensor accuracy to 1/200 ft or 1.0 mm
- Certified intrinsically safe
- 5/8" (16 mm) diameter probe
- Easy access 9V battery
- Automatic shut off after 10 minutes
- Easy to splice and repair
- Replacement tapes are interchangeable with other Meters
Obtaining Product Measurements
Read the depth off the permanently marked tape. Lower the probe further into the water, where the signals become intermittent, then pull back up and take a reading at the product/water interface. The thickness of the product layer is then determined by subtracting the first reading from the second. If there is only water in the well and no product, there will only be intermittent (water) signals. The presence or absence of dense (sinking) non-aqueous layers (DNAPL) is determined by continuing to lower the probe to the bottom of the well. If the steady tone and light return, this indicates a nonconductive liquid. Measure the depth and continue lowering the probe until it touches bottom and the tape goes slack. To determine the thickness of the DNAPL layer, subtract the first reading from the bottom depth.
The tape guide may be used to provide support for a small reel on the well casing. It acts as a datum allowing repeatably accurate measurements; ensures that the probe hangs in the centre of the well; and protects the tape from damage.
It is essential to use the grounding cable to ensure safety and proper function of the electronics in all applications.
up to 500 psi. The beam is emitted from within a Hydex cone-shaped tip. The tip is protected by an integral stainless steel shield, and is excellent for the vast majority of product monitoring situations.
Laser Marked PVDF Flat Tape
The easy-to-read markings on the 3/8" (10 mm) PVDF flat tape are permanently laser-marked. The dog bone shaped tape avoids adherence to wet surfaces in wells. It is resistant to most chemicals, and the smooth surface of the tape is easy to decontaminate and easy to handle.
- LM2: Feet and tenths: with markings every 1/100 ft.
- LM3: Meters and centimeters: with markings every mm.