• -50 to 300 ° c
• Waterproof IP67 
• Memory reading Min / Max

• -50 to 300 ° C
• IP67 waterproof
• Min / Max memory reading

•  -40 à 230°c
• Waterproof
• Min-max

• Flat bottom from entrance to exit for better head conversion
  
• Do not require a free-fall discharge to operate correctly
• Staff gauge and instrument mounting brackets located within flume and factory installed

• Watershed Runoff
  
• Agricultural Water Runoff
• To measure very small flows 
  

• Low Head Loss
  
• Minimum flow restriction
• Measurement accuracy

• Membrane diameters are available in 47mm and 50mm. 
• Resistant to acid and alkaline. 
• Suggest with our 15l/min pump vacuum pump 

• Binocular and trinocular models
• 216 x 150 mm mechanical rackless stage
• HWF 12.5/15 mm eyepieces

• GAS Formaldehyde (HCHO) & Carbon Dioxide (CO²) detectors
• Air temperature and humidity, Dew point & Wet bulb temperature
• 2.8″ TFT 320×240 pixels Color LCD display

• Resolution of 0.01m/sec
• 20 points average for Air Flow
• 3% velocity accuracy via low friction 2.83″D (72mm) ball bearing vane wheel on 3.9ft (120cm) cable

• LED backlight
• Data hold
• Velocity alarm

• Type K Temp: Range: -200°C to 1372°C(-328°F to 2501°F)
• Air Temp: Range: -30°C~100°C(-22°F~199°F)
• Humidity: Range: 0~100%RH
  

• Long life silicon photo diode inside
• Measurement rate:1.5 times per second
• Widest rang to 40,000FC/400,000lux

• Complies with IEC61672-1 class 2
• MAX & MIN measurements
• FAST & SLOW response
• Analog AC/DC outputs for connection to frequency analyzer or X-Y shaft recorder

• Type K Measures Temperature up to 1100°C (2000°F)
• SMP Miniature Male Connector Termination on End of Retractile Cord
• Maximum Handle Temperature: 70°C (160°F)
  

• High Accuracy gas sensor
• Mini USB interface connections
• Auto Power Off

• Indoor Air Quality displayed in ppm
• Visible and Audible CO2 warning alarm
• Displays Year, Month, Date, and Time

• Main application: water, wastewater, diesel fuel, fuel oil
• Sensor: clamp-on/external
• Measuring principle: transit time

• The cones have continuous graduations up to 1000 ml and are ideal for tests where a large volume of settled material is present
• Leakproof polyethylene plug permits easy withdrawal of sediment for gravimetric analysis and simplifies cleaning
• The cones are graduated in these divisions: 0-2ml in 0.1ml, 2-10ml in 0.5ml, 10-40ml in 1ml, 40-100ml in 2ml, and 100-1000ml in 50ml
• Lightweight Poxygrid® racks hold cone tips up off the benchtop for easier viewiong and to allow plug removal if required
• Wire frame racks have a wide base for stability; epoxy coated for durability and easy cleaning

• The cones have continuous graduations up to 1000 ml and are ideal for tests where a large volume of settled material is present
• The sealed polyethylene cap allows easy removal of sediment for gravimetric analysis and simplifies cleaning
• The cones are graduated in these divisions: 0-2ml to 0.1ml, 2-10ml to 0.5ml, 10-40ml to 1ml, 40-100ml to 2ml, and 100-1000ml to 50ml
• Lightweight Poxygrid® holders hold the cones at the top of the bench to facilitate visualization and allow removal of the cap if necessary
• The wire supports have a wide base for stability; they are epoxy coated for durability and easy cleaning

• Servo motor drive, powerful and maintenance-free.
• 3 digital LED display motor speed, rotary encoded switch control.
• Suitable for industrial sites, transfer liquid with large flow and high precision.

• Special for university laboratory and research institute.
• Ion chromatography and titrator.
• Pilot scale and industry production.

• With ABS engineering plastic housing, streamlined body design.
• Servo motor control, more strong and precise .
• Large flow rate range with UC25 pump head.
  
  
  

• Easy-to-use automation software
  
• Integrated safety precautions for user protection
• Precision accuracy with integrated correction system

• Range : -200°C to 1370°C (-328 to 2498°F)
• Resolution : 0.1° and 1°
• Accuracy : ±1°C
• K type probe not included
  

• 500 ml
• Accuracy of +/- 0.01 pH at 25°C
• Buffer Solutions pH 4, pH 7 or pH 10

• Big Operating Space with Backward Nosepiece, Sharp Image with High Quality Objectives
• Easier Comparing Test with Dual Slides Finger of Mechanical Stage
• Comfortable Handling with Precise Focusing System

• Temperature: -58 to 1022°F (-50 to 550°C)
• User selectable °F or °C
• Built-in laser pointer identifies target area

• With special porcelain enamel
  
• Easy reading
• Metric gauge is 80 mm wide

Used in video pipe, water well, drain, sewer, pipeline, plumbing & gas, chimney, duct, manhole, borehole inspection

• Length: 225 mm - 8 in
  
• Diameter: 6.4 mm - ½ in
• Temperature: -100°C ~ +1000°C 
  

• Length: 175 mm -  6 in
  
• Diameter: 3.2 mm - 1/8 in
• Temperature: -100°C ~ +800°C 

• Exceptional Durability
• Sampling are done in a single step
• Anti-corrosive materials

• Speed range: 0～1600rpm
• Surface max. temp: 450℃
• Heating element: nichrome wire